- 1 What is the best cement for fence posts?
- 2 How much cement do I need for a fence post?
- 3 Can you set fence posts with dry concrete?
- 4 Should you concrete a wood fence post?
- 5 Is 2 feet deep enough for fence posts?
- 6 How many bags of Postcrete do you need per post?
- 7 Can I pour concrete in a hole full of water?
- 8 What kind of gravel should I use for fence posts?
- 9 How do I keep my post level while concrete dries?
- 10 Why do you put dry concrete in a post hole?
- 11 Will wooden posts rot in concrete?
- 12 Can you install fence posts without cement?
- 13 How do you build a fence without a sinking post?
What is the best cement for fence posts?
For a small to mid sized job I recommend going with premixed. The best concrete mix for fence posts I’ve found is Quikrete Fast Setting Concrete Mix in a 50 lb bag. It’s 4000 psi, easy to work with, sets up fast, and doesn’t need to be mixed. Just pour it in the hole and soak with water.
How much cement do I need for a fence post?
Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.
Can you set fence posts with dry concrete?
Fast-setting concrete is ideal for setting posts because there’s no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.
Should you concrete a wood fence post?
Concrete is the most secure material for setting fence posts, especially if you have sandy soil. Gravel may be okay with dense, clay-heavy soil, but in looser soil, concrete is the only thing that will truly keep your fence posts stuck in place.
Is 2 feet deep enough for fence posts?
2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.
How many bags of Postcrete do you need per post?
You’ll need to bury the posts at least 2ft In the ground. As for how many bags of postcrete you need per post, that’s purely dependant on how big you make the post holes. As a rule of thumb, when using standard post hole diggers, I average 1 bag per post. For larger holes I would allow 1.5 bags to 2 bags per hole.
Can I pour concrete in a hole full of water?
The water in the hole under the pipe can be sucked out with a wet-dry vacuum before and during the repair job.
What kind of gravel should I use for fence posts?
Pea gravel is commonly used for fence post holes. Gravel that is roughly three eighths of an inch in size is generally a good medium between drainage and support, though gravel close to that size also may be used. If you want to use the best gravel for your area, you may want to consult a contractor.
How do I keep my post level while concrete dries?
You need to level it in two directions with a 4-foot level. After getting it straight in the first direction, hold one of the braces against the post and drive a single screw to connect the brace to the post. You can then level and brace the post in the other direction and begin filling the hole.
Why do you put dry concrete in a post hole?
When the concrete is dry-poured then wetted, there are no gaps around the concrete between the post or the soil, which helps negate any erosion that may cause the post to lean. We care less about having a maximum PSI footing and more about having a very tightly-packed hole to keep the post level.
Will wooden posts rot in concrete?
Simply setting the posts in concrete does create a condition that will accelerate rot in the bottom of the posts. With pressure-treated posts, the rot will be slow. The concrete at the top should be sloped away from the post to grade level to avoid water pooling around the base.
Can you install fence posts without cement?
Backfilling the fence post hole with gravel is another common alternative to using cement. Start with a hole about the size of the one you’d dig if you were using cement, insert a third of the post’s length into the hole, and then fill with crushed gravel, tamping every five inches until flush.
How do you build a fence without a sinking post?
If you need a temporary fence or a border that you can move as needed, a quick way is to use concrete blocks. Attach a bracket to a concrete block that is heavy enough to hold the wood or other material you plan to use to build the fence. The posts can be mounted to the brackets and the fence finished from there.